SCITOO Rear A/C Heater Blower Motor Fan for 2001 2002-2016 Dodge Grand Caravan 700234
SCITOO Rear A/C Heater Blower Motor Fan for 2001 2002-2016 Dodge Grand Caravan 700234
|
|
|
|
|
|
|
|
|
|
Brand NEW Blower Motor For Car
Features:
- NEW, not remanufacturedor rebuilt
- DIRECT REPLACEMENT
- Built to strict quality control standards
- HIGH QUALITY - Top quality materials which provide maximum strength and durability
- 1 YEAR WARRANTY-This item is backed by a 1 Year Warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser.
- 100% tested prior to leaving the factory
- The blower motor can be installed easily with no special tools required and just by removing a few screws under the passenger side dash of your vehicle. Simply remove the old blower motor and put the new one in. It is also a advisable to replace your blower motor relay/resistor with a new one when you replace your blower motor.
- Installation location:Rear
What Are Signs Your Blower Motor Needs to Be Replaced?
- Poor or Airflow from Air Vents
- No Airflow At All From Vents
- Skyrocketing Energy Bills
- Strange Noises When You Turn on the Heat
- Overheating Blower / Weird Smells
Fitting for the following years and models:
- 2001-2016 Chrysler Town & Country
- 2001-2007 Dodge Caravan
- 2001-2016 Dodge Grand Caravan
Removing the Blower Motor
Step 1
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2
Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3
Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4
Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5
Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6
Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7
Pull the fan blades away from the motor.
Installing the Blower Motor
Step 1
Drop the fan blades into position on the new motor.
Step 2
Screw on the nut that secures the fan blades to the motor.
Step 3
Slide the motor/fan blade assembly into position in the heater case or firewall.
Step 4
Screw in the screws that secure the blower motor to the heater case or firewall.
Step 5
Press the plastic wiring connector onto the back of the blower motor.
Step 6
Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt with a wrench.
Step 7
Test for proper operation.
NOTE:
- Please compare your parts against pictures to ensure this part fits your vehicle
- Please confirm your old part number matches up with one of the part numbers above
- Professional installation is highly recommended (No Instruction Included)
- For any needs please contact us.
Brand NEW Blower Motor For Car
Features:
- NEW, not remanufacturedor rebuilt
- DIRECT REPLACEMENT
- Built to strict quality control standards
- HIGH QUALITY - Top quality materials which provide maximum strength and durability
- 1 YEAR WARRANTY-This item is backed by a 1 Year Warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser.
- 100% tested prior to leaving the factory
- The blower motor can be installed easily with no special tools required and just by removing a few screws under the passenger side dash of your vehicle. Simply remove the old blower motor and put the new one in. It is also a advisable to replace your blower motor relay/resistor with a new one when you replace your blower motor.
- Installation location:Rear
What Are Signs Your Blower Motor Needs to Be Replaced?
- Poor or Airflow from Air Vents
- No Airflow At All From Vents
- Skyrocketing Energy Bills
- Strange Noises When You Turn on the Heat
- Overheating Blower / Weird Smells
Fitting for the following years and models:
- 2001-2016 Chrysler Town & Country
- 2001-2007 Dodge Caravan
- 2001-2016 Dodge Grand Caravan
Removing the Blower Motor
Step 1
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2
Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3
Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4
Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5
Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6
Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7
Pull the fan blades away from the motor.
Installing the Blower Motor
Step 1
Drop the fan blades into position on the new motor.
Step 2
Screw on the nut that secures the fan blades to the motor.
Step 3
Slide the motor/fan blade assembly into position in the heater case or firewall.
Step 4
Screw in the screws that secure the blower motor to the heater case or firewall.
Step 5
Press the plastic wiring connector onto the back of the blower motor.
Step 6
Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt with a wrench.
Step 7
Test for proper operation.
NOTE:
- Please compare your parts against pictures to ensure this part fits your vehicle
- Please confirm your old part number matches up with one of the part numbers above
- Professional installation is highly recommended (No Instruction Included)
- For any needs please contact us.
Item Specifics | |
---|---|
Brand : | SCITOO |
Housing Material : | Plastic |
Warranty : | 1 Year |
Placement on Vehicle : | Rear |
Manufacturer Part Number : | CB058479S01 |
Speeds : | Single Speed |
Color : | White Black |
Shaft Type : | Single Shaft |
Product Name : | Heater Blower Motor w/ Fan Cage |
Interchange Part Number : | 5183147AA |
Fitment Type : | Direct Replacement |
Other Part Number : | 5183147AA |
Product Dimensions : | 7.9x7.7x7.7inches |
Condition : | New |
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ]
[We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.]
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Q: How do I pay for my purchase?
A: MY store accepts PayPal.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
1. We will leave positive feedback once we get your payment.
2. If you are dissatisfied for any reason, please do contact us before you leaving a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a feedback.
Shop Category Picture |
Rear A/C Heater Blower Motor Fan for 2001 2002-2016 Dodge Grand Caravan 700234
Brand NEW Blower Motor For Car
Features:
What Are Signs Your Blower Motor Needs to Be Replaced?
Fitting for the following years and models:
Removing the Blower Motor
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2 Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3 Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4 Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5 Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6 Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7 Pull the fan blades away from the motor.
Installing the Blower Motor
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
NOTE:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. [We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.] 1.All of our brand new items come with a 60-Days money-back guarantee. Q: How do I pay for my purchase? 1. We will leave positive feedback once we get your payment. |
Brand: | SCITOO |
---|---|
Isin: | IIJPLRNGYKHH |

IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms

GUARANTEED SAFE CHECKOUT
-
MONEY BACK GUARANTEE
30 days money back guarantee, no additional fee charged.
-
EXCELLENT SUPPORT
We provide 24/7 online customer support via email.
-
Fast Shipping
One week domestic shipping. Global delivery to the US in 2 weeks.

|
|
|
|
|
|
|
|
|
|
Brand NEW Blower Motor For Car
Features:
- NEW, not remanufacturedor rebuilt
- DIRECT REPLACEMENT
- Built to strict quality control standards
- HIGH QUALITY - Top quality materials which provide maximum strength and durability
- 1 YEAR WARRANTY-This item is backed by a 1 Year Warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser.
- 100% tested prior to leaving the factory
- The blower motor can be installed easily with no special tools required and just by removing a few screws under the passenger side dash of your vehicle. Simply remove the old blower motor and put the new one in. It is also a advisable to replace your blower motor relay/resistor with a new one when you replace your blower motor.
- Installation location:Rear
What Are Signs Your Blower Motor Needs to Be Replaced?
- Poor or Airflow from Air Vents
- No Airflow At All From Vents
- Skyrocketing Energy Bills
- Strange Noises When You Turn on the Heat
- Overheating Blower / Weird Smells
Fitting for the following years and models:
- 2001-2016 Chrysler Town & Country
- 2001-2007 Dodge Caravan
- 2001-2016 Dodge Grand Caravan
Removing the Blower Motor
Step 1
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2
Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3
Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4
Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5
Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6
Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7
Pull the fan blades away from the motor.
Installing the Blower Motor
Step 1
Drop the fan blades into position on the new motor.
Step 2
Screw on the nut that secures the fan blades to the motor.
Step 3
Slide the motor/fan blade assembly into position in the heater case or firewall.
Step 4
Screw in the screws that secure the blower motor to the heater case or firewall.
Step 5
Press the plastic wiring connector onto the back of the blower motor.
Step 6
Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt with a wrench.
Step 7
Test for proper operation.
NOTE:
- Please compare your parts against pictures to ensure this part fits your vehicle
- Please confirm your old part number matches up with one of the part numbers above
- Professional installation is highly recommended (No Instruction Included)
- For any needs please contact us.
Brand NEW Blower Motor For Car
Features:
- NEW, not remanufacturedor rebuilt
- DIRECT REPLACEMENT
- Built to strict quality control standards
- HIGH QUALITY - Top quality materials which provide maximum strength and durability
- 1 YEAR WARRANTY-This item is backed by a 1 Year Warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser.
- 100% tested prior to leaving the factory
- The blower motor can be installed easily with no special tools required and just by removing a few screws under the passenger side dash of your vehicle. Simply remove the old blower motor and put the new one in. It is also a advisable to replace your blower motor relay/resistor with a new one when you replace your blower motor.
- Installation location:Rear
What Are Signs Your Blower Motor Needs to Be Replaced?
- Poor or Airflow from Air Vents
- No Airflow At All From Vents
- Skyrocketing Energy Bills
- Strange Noises When You Turn on the Heat
- Overheating Blower / Weird Smells
Fitting for the following years and models:
- 2001-2016 Chrysler Town & Country
- 2001-2007 Dodge Caravan
- 2001-2016 Dodge Grand Caravan
Removing the Blower Motor
Step 1
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2
Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3
Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4
Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5
Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6
Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7
Pull the fan blades away from the motor.
Installing the Blower Motor
Step 1
Drop the fan blades into position on the new motor.
Step 2
Screw on the nut that secures the fan blades to the motor.
Step 3
Slide the motor/fan blade assembly into position in the heater case or firewall.
Step 4
Screw in the screws that secure the blower motor to the heater case or firewall.
Step 5
Press the plastic wiring connector onto the back of the blower motor.
Step 6
Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt with a wrench.
Step 7
Test for proper operation.
NOTE:
- Please compare your parts against pictures to ensure this part fits your vehicle
- Please confirm your old part number matches up with one of the part numbers above
- Professional installation is highly recommended (No Instruction Included)
- For any needs please contact us.
Item Specifics | |
---|---|
Brand : | SCITOO |
Housing Material : | Plastic |
Warranty : | 1 Year |
Placement on Vehicle : | Rear |
Manufacturer Part Number : | CB058479S01 |
Speeds : | Single Speed |
Color : | White Black |
Shaft Type : | Single Shaft |
Product Name : | Heater Blower Motor w/ Fan Cage |
Interchange Part Number : | 5183147AA |
Fitment Type : | Direct Replacement |
Other Part Number : | 5183147AA |
Product Dimensions : | 7.9x7.7x7.7inches |
Condition : | New |
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ]
[We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.]
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Q: How do I pay for my purchase?
A: MY store accepts PayPal.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
1. We will leave positive feedback once we get your payment.
2. If you are dissatisfied for any reason, please do contact us before you leaving a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a feedback.
Shop Category Picture |
Rear A/C Heater Blower Motor Fan for 2001 2002-2016 Dodge Grand Caravan 700234
Brand NEW Blower Motor For Car
Features:
What Are Signs Your Blower Motor Needs to Be Replaced?
Fitting for the following years and models:
Removing the Blower Motor
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2 Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3 Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4 Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5 Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6 Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7 Pull the fan blades away from the motor.
Installing the Blower Motor
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
NOTE:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. [We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.] 1.All of our brand new items come with a 60-Days money-back guarantee. Q: How do I pay for my purchase? 1. We will leave positive feedback once we get your payment. |

- Brand: SCITOO
- Housing Material: Plastic
- Manufacturer Warranty: 1 Year
- Placement on Vehicle: Rear
- Manufacturer Part Number: CB058479S01
- UPC: Does not apply
- Speeds: Single Speed
- Color: White, Black
- Shaft Type: Single Shaft
- Product Name: Heater Blower Motor w/ Fan Cage
- Interchange Part Number: 5183147AA
- Fitment Type: Direct Replacement
- Other Part Number: 5183147AA
- Product Dimensions: 7.9x7.7x7.7inches
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
Shipping Method | Estimated Delivery | Cost |
---|---|---|
Free Shipping (US) | 5–10 business days | Free, available on eligible items |
Standard Shipping (US to US by Item) | 5–10 business days | $6.50 for the first item, $3.00 each additional |
Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $6.50, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
Extended Delivery (Ships from Overseas Warehouse) | 10–15 business days | $14.50 for the first item, $4.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
-
Email: support@ibspot.com
-
Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
-
The item must be unused, in the same condition as received, and in its original packaging.
-
A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
-
Perishable goods (for example, food, flowers, newspapers, magazines)
-
Intimate or sanitary goods
-
Hazardous materials or flammable liquids/gases
-
Gift cards
-
Downloadable software
-
Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
-
Books with obvious signs of use
-
Opened CDs, DVDs, software, or vinyl records
-
Items not in their original condition, damaged, or missing parts not due to our error
-
Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
-
In-store returns are refunded to the original form of payment or issued as a gift card.
-
Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
-
5–7 business days for the return to reach our Returns Center.
-
An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.