International Epoxies & Sealers Super Clear Epoxy Coating With UV for bar tops, tables, crafts, 1-Gallon Kit
International Epoxies & Sealers Super Clear Epoxy Coating With UV for bar tops, tables, crafts, 1-Gallon Kit
International Epoxies & Sealers Super Clear Epoxy Coating With UV for bar tops, tables, crafts, 1-Gallon Kit
Super-Clear Epoxy Coating With UV for bar tops, tables, crafts, 1-Gallon Kit.
1/2-Gallon of Side A and 1/2 Gallon of Side B
Super-Clear Epoxy is a self-leveling epoxy coating used forcoating wood tabletops, stone, metal veneer, painted surfaces, crafts, art,jewelry, castings, etc. Formulated with a UV Inhibitor to delay the naturalambering of the cured epoxy film due to UV exposure during years of indoorexposure.Cures to a high gloss,hard, smooth, clear finish and exhibits goodair release.
TECHNICAL DATA
SAFETY PRECAUTIONS
Read the material SDS before beginning found at www.useies.com.
• Wear safety glasses at all times while handling.
• Wear latex gloves and avoid getting product on skin.
• Plastic aprons can prevent product from getting onto clothing and soaking through to the skin.
• Avoid inhalation of any fumes from the product and use in a well-ventilated area.
SURFACE PREPARATION
Although it is not possible to address every type of surface, the following are some general guidelines on preparing the surfaces to which the epoxy will be applied:
• Bare wood should be sealed with a thin coat of mixed epoxy.
• Decoupage surfaces should be tested for color-fastness prior to application.
• When recoating an existing epoxy coating, the existing coating should be scuff sanded and cleaned with a
solvent such as Denatured Alcohol or Isopropanol 99%.
• Be sure that both the surface and the epoxy to be mixed are at the same temperature. (Preferably 75-85°F.)
MIXING
The proper ratio is 1-part hardener to 1-part resin. Improper mixing will cause soft or tacky spots in the surface.
• First, be sure you are preparing to mix containers of Hardener and Resin by volume. Double-check your labels
to ensure the proper materials are being mixed.
• Graduated mixing containers are recommended for measuring and mixing. Batches should not exceed 1.5
gallons total. If more than 1.5 gallons is needed at once make multiple small batches.
• Hand mixing with a paint stir stick is recommended. While mixing, stir continuously while also sweeping the
sides and bottom of the mixing container. Do so in a fl uid and steady manner, as it is important to mix without
introducing air into the mixture.
• Total mixing time should take approximately 3 minutes.
• The product may cloud a little during mixing but will clear as mixing nears completion. After mixing is complete,
allow the mix to stand 3-5 minutes. After 3-5 minutes, remix for approximately 30 seconds.
The completed mix should then be poured into a separate container for the final pour. Even with the most thorough mixing practices, there are still likely unmixed portions on the sides and bottom of the mixing container.
APPLICATION
Epoxy is self-leveling; therefore, the surface must be level for uniformity. First, a thin layer called a seal coat should be applied. The best way to apply a seal coat is to start on one end and pour the resin the length of the surface. Use a rubber squeegee or a foam brush to drag the resin across the entire surface and achieve a thin even coat. Allow 6 hours before moving on to flood coats.
It is not recommended to apply more than 1/8-inch-thick per flood coat. The epoxy may be poured on the surface and spread with a plastic hand squeegee or a dust free foam brush. Thick films are achieved through multiple coats.
Once the epoxy is applied to the desired thickness, tiny air bubbles will appear on the surface.
To eliminate these bubbles, wait at least 10 minutes after application, and then pass the flame of a propane torch systematically over the surface while keeping the flame at least 6-8 inches from the surface. You are not trying to heat the surface, simply popping the bubbles with the exhaust gas. The same technique can be used with a heat gun. It will be necessary to repeat this process until the bubbles stop surfacing. You will now have a glass like surface. When re-coating within a 12 to 36-hour window no surface preparation is needed but it is recommended to wipe the surface down with denatured alcohol. The layers will bond together as one. Beyond the 36-hour window, very light sanding is necessary with some 180 to 220 grit sandpaper. After lightly sanding, you should wipe down the surface with a solvent such as denatured alcohol and let dry. Blemishes caused by contaminants or debris
can be sanded out and recoated without compromising the clarity.
CURE TIME
Cure times will vary with temperature and thickness. Super-Clear Epoxy Coating will be tack free in a 1/8-inch thickness at 77°F in approximately 8 hours. The epoxy will be ready for service after 24 hours. Even though the
film will appear hard, the epoxy will not reach full cure for 14 days. It is important to not leave objects on the treated surface until the epoxy is fully cured.
When used for bars or table tops any hot items like coffee cups, hot plates, etc., with temperatures over 140°F will leave a ring or impression on almost any epoxy. The use of saucers under cups and heat resistant pads under hot plates are recommended to preserve the integrity of the epoxy.
COVERAGE CHART
Seal Coat Flood Coats
Area Resin Mixture Area Resin Mixture
1 Sq Ft 3oz 1 Sq Ft 8oz
4 Sq Ft 11oz 4 Sq Ft 32oz
10 Sq Ft 26oz 10 Sq Ft 80oz
16 Sq Ft 42oz 16 Sq Ft 128oz
24 Sq Ft 64oz 24 Sq Ft 192ozI
IMPORTANT NOTES ABOUT EPOXIES
Epoxies cure through chemical reaction. The chemical reaction generates heat. The greater the mass of epoxy, the faster the reaction will occur. Pot life is measured with about 4 oz. of epoxy @ 77°F. Therefore, a stated 40-minute pot life is for that 4 oz. A 1.5-gallon mix in a bucket will only have a 10-15 min pot life. Epoxies will amber slightly when exposed to sunlight, even for only several hours. They will chalk in exterior applications. For exterior applications, a top coat with a UV-inhibited Urethane is recommended.
Super-Clear Epoxy Coating is designed to delay the natural ambering of the cured Epoxy film due to UV exposure during years of indoor exposure.
If this is your first experience with an epoxy, EXPERIMENT ON A SIMILAR TEST SURFACE before applying to your project material. Even the pros have bad days!
NOTICE TO PURCHASER: The following warranty is in lieu of all other expressed or implied warranties,
specifically all goods are manufactured of first class materials and by competent professionals. We
have no control over the use and application of our products. Our liability shall not exceed the purchase price.
| Brand: | International Epoxies & Sealers |
|---|---|
| Isin: | ISEGY2KQKDK6 |
Out of Stock
In Stock
Backordered
Out of Stock
IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms
GUARANTEED SAFE CHECKOUT
-
MONEY BACK GUARANTEE
30 days money back guarantee, no additional fee charged.
-
EXCELLENT SUPPORT
We provide 24/7 online customer support via email.
-
Fast Shipping
One week domestic shipping. Global delivery to the US in 2 weeks.
Super-Clear Epoxy Coating With UV for bar tops, tables, crafts, 1-Gallon Kit.
1/2-Gallon of Side A and 1/2 Gallon of Side B
Super-Clear Epoxy is a self-leveling epoxy coating used forcoating wood tabletops, stone, metal veneer, painted surfaces, crafts, art,jewelry, castings, etc. Formulated with a UV Inhibitor to delay the naturalambering of the cured epoxy film due to UV exposure during years of indoorexposure.Cures to a high gloss,hard, smooth, clear finish and exhibits goodair release.
TECHNICAL DATA
SAFETY PRECAUTIONS
Read the material SDS before beginning found at www.useies.com.
• Wear safety glasses at all times while handling.
• Wear latex gloves and avoid getting product on skin.
• Plastic aprons can prevent product from getting onto clothing and soaking through to the skin.
• Avoid inhalation of any fumes from the product and use in a well-ventilated area.
SURFACE PREPARATION
Although it is not possible to address every type of surface, the following are some general guidelines on preparing the surfaces to which the epoxy will be applied:
• Bare wood should be sealed with a thin coat of mixed epoxy.
• Decoupage surfaces should be tested for color-fastness prior to application.
• When recoating an existing epoxy coating, the existing coating should be scuff sanded and cleaned with a
solvent such as Denatured Alcohol or Isopropanol 99%.
• Be sure that both the surface and the epoxy to be mixed are at the same temperature. (Preferably 75-85°F.)
MIXING
The proper ratio is 1-part hardener to 1-part resin. Improper mixing will cause soft or tacky spots in the surface.
• First, be sure you are preparing to mix containers of Hardener and Resin by volume. Double-check your labels
to ensure the proper materials are being mixed.
• Graduated mixing containers are recommended for measuring and mixing. Batches should not exceed 1.5
gallons total. If more than 1.5 gallons is needed at once make multiple small batches.
• Hand mixing with a paint stir stick is recommended. While mixing, stir continuously while also sweeping the
sides and bottom of the mixing container. Do so in a fl uid and steady manner, as it is important to mix without
introducing air into the mixture.
• Total mixing time should take approximately 3 minutes.
• The product may cloud a little during mixing but will clear as mixing nears completion. After mixing is complete,
allow the mix to stand 3-5 minutes. After 3-5 minutes, remix for approximately 30 seconds.
The completed mix should then be poured into a separate container for the final pour. Even with the most thorough mixing practices, there are still likely unmixed portions on the sides and bottom of the mixing container.
APPLICATION
Epoxy is self-leveling; therefore, the surface must be level for uniformity. First, a thin layer called a seal coat should be applied. The best way to apply a seal coat is to start on one end and pour the resin the length of the surface. Use a rubber squeegee or a foam brush to drag the resin across the entire surface and achieve a thin even coat. Allow 6 hours before moving on to flood coats.
It is not recommended to apply more than 1/8-inch-thick per flood coat. The epoxy may be poured on the surface and spread with a plastic hand squeegee or a dust free foam brush. Thick films are achieved through multiple coats.
Once the epoxy is applied to the desired thickness, tiny air bubbles will appear on the surface.
To eliminate these bubbles, wait at least 10 minutes after application, and then pass the flame of a propane torch systematically over the surface while keeping the flame at least 6-8 inches from the surface. You are not trying to heat the surface, simply popping the bubbles with the exhaust gas. The same technique can be used with a heat gun. It will be necessary to repeat this process until the bubbles stop surfacing. You will now have a glass like surface. When re-coating within a 12 to 36-hour window no surface preparation is needed but it is recommended to wipe the surface down with denatured alcohol. The layers will bond together as one. Beyond the 36-hour window, very light sanding is necessary with some 180 to 220 grit sandpaper. After lightly sanding, you should wipe down the surface with a solvent such as denatured alcohol and let dry. Blemishes caused by contaminants or debris
can be sanded out and recoated without compromising the clarity.
CURE TIME
Cure times will vary with temperature and thickness. Super-Clear Epoxy Coating will be tack free in a 1/8-inch thickness at 77°F in approximately 8 hours. The epoxy will be ready for service after 24 hours. Even though the
film will appear hard, the epoxy will not reach full cure for 14 days. It is important to not leave objects on the treated surface until the epoxy is fully cured.
When used for bars or table tops any hot items like coffee cups, hot plates, etc., with temperatures over 140°F will leave a ring or impression on almost any epoxy. The use of saucers under cups and heat resistant pads under hot plates are recommended to preserve the integrity of the epoxy.
COVERAGE CHART
Seal Coat Flood Coats
Area Resin Mixture Area Resin Mixture
1 Sq Ft 3oz 1 Sq Ft 8oz
4 Sq Ft 11oz 4 Sq Ft 32oz
10 Sq Ft 26oz 10 Sq Ft 80oz
16 Sq Ft 42oz 16 Sq Ft 128oz
24 Sq Ft 64oz 24 Sq Ft 192ozI
IMPORTANT NOTES ABOUT EPOXIES
Epoxies cure through chemical reaction. The chemical reaction generates heat. The greater the mass of epoxy, the faster the reaction will occur. Pot life is measured with about 4 oz. of epoxy @ 77°F. Therefore, a stated 40-minute pot life is for that 4 oz. A 1.5-gallon mix in a bucket will only have a 10-15 min pot life. Epoxies will amber slightly when exposed to sunlight, even for only several hours. They will chalk in exterior applications. For exterior applications, a top coat with a UV-inhibited Urethane is recommended.
Super-Clear Epoxy Coating is designed to delay the natural ambering of the cured Epoxy film due to UV exposure during years of indoor exposure.
If this is your first experience with an epoxy, EXPERIMENT ON A SIMILAR TEST SURFACE before applying to your project material. Even the pros have bad days!
NOTICE TO PURCHASER: The following warranty is in lieu of all other expressed or implied warranties,
specifically all goods are manufactured of first class materials and by competent professionals. We
have no control over the use and application of our products. Our liability shall not exceed the purchase price.
Item Specifics
- Brand: International Epoxies & Sealers
- Type: clear epoxy resin
- Custom Bundle: No
- Color: Clear
- MPN: 8161
- Country/Region of Manufacture: United States
- Modified Item: No
- UPC: Does not apply
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
| Shipping Method | Estimated Delivery | Cost |
|---|---|---|
| Free Shipping (US) | 5–10 business days | Free, available on eligible items |
| Standard Shipping (US to US by Item) | 5–10 business days | $6.50 for the first item, $2.00 each additional |
| Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $6.50, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
| Extended Delivery (Ships from Overseas Warehouse) | 10–20 business days | $14.50 for the first item, $2.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
- Email: support@ibspot.com
- Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
- The item must be unused, in the same condition as received, and in its original packaging.
- A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
- Perishable goods (for example, food, flowers, newspapers, magazines)
- Intimate or sanitary goods
- Hazardous materials or flammable liquids/gases
- Gift cards
- Downloadable software
- Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
- Books with obvious signs of use
- Opened CDs, DVDs, software, or vinyl records
- Items not in their original condition, damaged, or missing parts not due to our error
- Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
- In-store returns are refunded to the original form of payment or issued as a gift card.
- Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
- 5–7 business days for the return to reach our Returns Center.
- An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.