Speedokote Paint over Rust with Underbody Gloss Black Paint, Quart, TRC-15-Q, RUST-BITE
Speedokote Paint over Rust with Underbody Gloss Black Paint, Quart, TRC-15-Q, RUST-BITE
Speedokote Paint over Rust with Underbody Gloss Black Paint, Quart, TRC-15-Q, RUST-BITE
Product Overview
This sale is for one quart of TRC-15-Q, Rust Preventive Underbody Gloss Black Paint.
TRC-15 Gloss Black
• Home • Auto Restoration • Industrial • Fleet • Marine •
TECHNICAL DATA
SUGGESTED USES:
Heavy equipment, trucks, snow plows, mower decks, tractors and other
farm machinery, oil field equipment, boat trailers, buses, military vehicles,
dumpsters, roll offs, fork lifts, propane tanks, truck bodies, storage tanks,
structural steel, pipes, iron works, gates, fence posts, chain link, steel truck
rims, metal roofs, sheds, and concrete floors.
DESCRIPTION:
Rust-Bite is a high solids, VOC compliant, single component rust preventive
and underbody coating specifically formulated to permanently stop
corrosion without the use of primers or topcoats. Rust-Bite protects many
surfaces from water, chemicals, salt, and other corrosive contaminants. Rust-
Bite stops rust when applied to rust that is prepared by using a wire brush or
hand scraper to remove all loose rust or scale. For optimum adhesion
sandblast with medium grit. Rust-Bite will dry to a flexible rock hard, nonporous
finish that will not crack, chip, flake or peel. Rust-Bite cures by
reacting with atmospheric moisture and its cured film resembles that of a
powder coating or a baked-on finish with the use of no hardeners or heat.
Rust-Bite seals and protects many surfaces from road salt, gasoline, diesel
fuel, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
Rust-Bite can be top coated with any industrial or automotive finish.
PREPARATION
Remove all dirt, grease or oils, clean surfaces using a Wax & Grease
Remover or equivalent. For heavy build-up scrape or wire brush excess
material prior to degreasing. Allow surfaces to dry thoroughly. NOTE: Do
not apply Rust-Bite if atmospheric temperature is below 50°F.
RUSTED SURFACES:
Remove loose rust and scale using a stiff wire brush, by grinding, or hand
tool cleaning. Remove all loose, peeling or bubbling paint. NOTE: Rust-Bite
works best when applied directly over rust. NOTE: Do not remove all rust or
apply any type of Rust Converter before applying Rust-Bite.
BARE, SMOOTH METAL:
Sandblasting is recommended but sanding with 36 to 80 grit sand-paper is
also acceptable. When blasting, provide a medium to coarse profile for
optimum adhesion. Avoid any media that may leave a smooth surface.
PAINTED SURFACES:
Previously painted surfaces should be sanded using a 120 to 180 grit
sandpaper to remove gloss.
MIXING & HANDLING:
Container may be under slight pressure. Stir liquid gently until uniformly
mixed. Do not shake, shaking will cause Rust-Bite to build pressure in can.
Never work directly from the Rust-Bite can unless the entire contents will be
used in a single painting session. Always pour what will be used into a
separate container.
NOTE: Never pour unused product back into original
container after use.
NOTE: Before closing Rust-Bite container apply a sheet
of plastic or food wrap over can, Rust-Bite will adhere lid to can if plastic is
not applied.
Never allow can to sit opened when not in use. WEAR
GLOVES DURING USE Skin contact should be avoided. Do not attempt to
remove dried Chassis Saver from skin with solvent; soak in warm, soapy
water. Once product has stained skin, only time will remove it.
APPLICATION & REDUCING:
Apply 2-4 coats allowing 3 to 8 hours between coats depending on temp
and humidity. Each coat should be dry to touch with no tackiness before
applying next coat. Rust-Bite is a moisture cure finish which when applied
too heavy will have a tendency to bubble while curing. Avoid bubbling by
applying thin coats only. Higher temps and humidity will shorten drying
time. Low temp and humidity will lengthen dry. Do not apply Rust-Bite if
temperature is below 50°F. Never use lacquer thinner as a reducer for Rust-
Bite or to wipe surfaces prior to painting.
BRUSH APPLICATION:
Apply thin, even coats using a nylon brush. For better flow and leveling, add
up to 10% TRC-01 Reducer.
SPRAY APPLICATION:
Reduce up to 10% using TRC-01 Reducer. Apply medium-wet coats while
maintaining a gun distance of 12 to 14 inches. Spray tip size should be: 1.2 to
1.4mm.
NOTE:
For surfaces that will be
exposed to UV (sunlight), apply a UV resistant single stage urethane paint after 3 - 24 hours.
RECOAT:
For films cured over 24 hours, sand using 400-grit abrasive to remove
gloss before recoating.
Health and Safety:
See Safety Data Sheet and labels for additional safety information and handling instructions.
* The contents of this package may have to be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels and SDS’s of all components, since
the mixture will have the hazards of all its parts.
* Improper handling and use, for example, poor spray technique, inadequate engineering controls and or lack of Personal Protective Equipment (PPE), may result in hazardous conditions or injury.
* Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
* Provide adequate ventilation for health and fire hazard control.
* Follow company, product SDS and respirator manufacturer’s recommendations for selection and proper use of respiratory protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory
requirements.
* Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on SDS.
* Always observe all applicable precautions and follow good safety and hygiene practices.
* Safety Data Sheets are available on website.
| Brand: | Speedokote |
|---|---|
| Isin: | IEA17GBGPHHC |
Out of Stock
In Stock
Backordered
Out of Stock
IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms
Product Overview
This sale is for one quart of TRC-15-Q, Rust Preventive Underbody Gloss Black Paint.
TRC-15 Gloss Black
• Home • Auto Restoration • Industrial • Fleet • Marine •
TECHNICAL DATA
SUGGESTED USES:
Heavy equipment, trucks, snow plows, mower decks, tractors and other
farm machinery, oil field equipment, boat trailers, buses, military vehicles,
dumpsters, roll offs, fork lifts, propane tanks, truck bodies, storage tanks,
structural steel, pipes, iron works, gates, fence posts, chain link, steel truck
rims, metal roofs, sheds, and concrete floors.
DESCRIPTION:
Rust-Bite is a high solids, VOC compliant, single component rust preventive
and underbody coating specifically formulated to permanently stop
corrosion without the use of primers or topcoats. Rust-Bite protects many
surfaces from water, chemicals, salt, and other corrosive contaminants. Rust-
Bite stops rust when applied to rust that is prepared by using a wire brush or
hand scraper to remove all loose rust or scale. For optimum adhesion
sandblast with medium grit. Rust-Bite will dry to a flexible rock hard, nonporous
finish that will not crack, chip, flake or peel. Rust-Bite cures by
reacting with atmospheric moisture and its cured film resembles that of a
powder coating or a baked-on finish with the use of no hardeners or heat.
Rust-Bite seals and protects many surfaces from road salt, gasoline, diesel
fuel, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
Rust-Bite can be top coated with any industrial or automotive finish.
PREPARATION
Remove all dirt, grease or oils, clean surfaces using a Wax & Grease
Remover or equivalent. For heavy build-up scrape or wire brush excess
material prior to degreasing. Allow surfaces to dry thoroughly. NOTE: Do
not apply Rust-Bite if atmospheric temperature is below 50°F.
RUSTED SURFACES:
Remove loose rust and scale using a stiff wire brush, by grinding, or hand
tool cleaning. Remove all loose, peeling or bubbling paint. NOTE: Rust-Bite
works best when applied directly over rust. NOTE: Do not remove all rust or
apply any type of Rust Converter before applying Rust-Bite.
BARE, SMOOTH METAL:
Sandblasting is recommended but sanding with 36 to 80 grit sand-paper is
also acceptable. When blasting, provide a medium to coarse profile for
optimum adhesion. Avoid any media that may leave a smooth surface.
PAINTED SURFACES:
Previously painted surfaces should be sanded using a 120 to 180 grit
sandpaper to remove gloss.
MIXING & HANDLING:
Container may be under slight pressure. Stir liquid gently until uniformly
mixed. Do not shake, shaking will cause Rust-Bite to build pressure in can.
Never work directly from the Rust-Bite can unless the entire contents will be
used in a single painting session. Always pour what will be used into a
separate container.
NOTE: Never pour unused product back into original
container after use.
NOTE: Before closing Rust-Bite container apply a sheet
of plastic or food wrap over can, Rust-Bite will adhere lid to can if plastic is
not applied.
Never allow can to sit opened when not in use. WEAR
GLOVES DURING USE Skin contact should be avoided. Do not attempt to
remove dried Chassis Saver from skin with solvent; soak in warm, soapy
water. Once product has stained skin, only time will remove it.
APPLICATION & REDUCING:
Apply 2-4 coats allowing 3 to 8 hours between coats depending on temp
and humidity. Each coat should be dry to touch with no tackiness before
applying next coat. Rust-Bite is a moisture cure finish which when applied
too heavy will have a tendency to bubble while curing. Avoid bubbling by
applying thin coats only. Higher temps and humidity will shorten drying
time. Low temp and humidity will lengthen dry. Do not apply Rust-Bite if
temperature is below 50°F. Never use lacquer thinner as a reducer for Rust-
Bite or to wipe surfaces prior to painting.
BRUSH APPLICATION:
Apply thin, even coats using a nylon brush. For better flow and leveling, add
up to 10% TRC-01 Reducer.
SPRAY APPLICATION:
Reduce up to 10% using TRC-01 Reducer. Apply medium-wet coats while
maintaining a gun distance of 12 to 14 inches. Spray tip size should be: 1.2 to
1.4mm.
NOTE:
For surfaces that will be
exposed to UV (sunlight), apply a UV resistant single stage urethane paint after 3 - 24 hours.
RECOAT:
For films cured over 24 hours, sand using 400-grit abrasive to remove
gloss before recoating.
Health and Safety:
See Safety Data Sheet and labels for additional safety information and handling instructions.
* The contents of this package may have to be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels and SDS’s of all components, since
the mixture will have the hazards of all its parts.
* Improper handling and use, for example, poor spray technique, inadequate engineering controls and or lack of Personal Protective Equipment (PPE), may result in hazardous conditions or injury.
* Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
* Provide adequate ventilation for health and fire hazard control.
* Follow company, product SDS and respirator manufacturer’s recommendations for selection and proper use of respiratory protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory
requirements.
* Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on SDS.
* Always observe all applicable precautions and follow good safety and hygiene practices.
* Safety Data Sheets are available on website.
| Brand: | Speedokote |
|---|---|
| Isin: | IEA17GBGPHHC |
This sale is for one quart of TRC-15-Q, Rust Preventive Underbody Gloss Black Paint.
TRC-15 Gloss Black
• Home • Auto Restoration • Industrial • Fleet • Marine •
TECHNICAL DATA
SUGGESTED USES:
Heavy equipment, trucks, snow plows, mower decks, tractors and other
farm machinery, oil field equipment, boat trailers, buses, military vehicles,
dumpsters, roll offs, fork lifts, propane tanks, truck bodies, storage tanks,
structural steel, pipes, iron works, gates, fence posts, chain link, steel truck
rims, metal roofs, sheds, and concrete floors.
DESCRIPTION:
Rust-Bite is a high solids, VOC compliant, single component rust preventive
and underbody coating specifically formulated to permanently stop
corrosion without the use of primers or topcoats. Rust-Bite protects many
surfaces from water, chemicals, salt, and other corrosive contaminants. Rust-
Bite stops rust when applied to rust that is prepared by using a wire brush or
hand scraper to remove all loose rust or scale. For optimum adhesion
sandblast with medium grit. Rust-Bite will dry to a flexible rock hard, nonporous
finish that will not crack, chip, flake or peel. Rust-Bite cures by
reacting with atmospheric moisture and its cured film resembles that of a
powder coating or a baked-on finish with the use of no hardeners or heat.
Rust-Bite seals and protects many surfaces from road salt, gasoline, diesel
fuel, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
Rust-Bite can be top coated with any industrial or automotive finish.
PREPARATION
Remove all dirt, grease or oils, clean surfaces using a Wax & Grease
Remover or equivalent. For heavy build-up scrape or wire brush excess
material prior to degreasing. Allow surfaces to dry thoroughly. NOTE: Do
not apply Rust-Bite if atmospheric temperature is below 50°F.
RUSTED SURFACES:
Remove loose rust and scale using a stiff wire brush, by grinding, or hand
tool cleaning. Remove all loose, peeling or bubbling paint. NOTE: Rust-Bite
works best when applied directly over rust. NOTE: Do not remove all rust or
apply any type of Rust Converter before applying Rust-Bite.
BARE, SMOOTH METAL:
Sandblasting is recommended but sanding with 36 to 80 grit sand-paper is
also acceptable. When blasting, provide a medium to coarse profile for
optimum adhesion. Avoid any media that may leave a smooth surface.
PAINTED SURFACES:
Previously painted surfaces should be sanded using a 120 to 180 grit
sandpaper to remove gloss.
MIXING & HANDLING:
Container may be under slight pressure. Stir liquid gently until uniformly
mixed. Do not shake, shaking will cause Rust-Bite to build pressure in can.
Never work directly from the Rust-Bite can unless the entire contents will be
used in a single painting session. Always pour what will be used into a
separate container.
NOTE: Never pour unused product back into original
container after use.
NOTE: Before closing Rust-Bite container apply a sheet
of plastic or food wrap over can, Rust-Bite will adhere lid to can if plastic is
not applied.
Never allow can to sit opened when not in use. WEAR
GLOVES DURING USE Skin contact should be avoided. Do not attempt to
remove dried Chassis Saver from skin with solvent; soak in warm, soapy
water. Once product has stained skin, only time will remove it.
APPLICATION & REDUCING:
Apply 2-4 coats allowing 3 to 8 hours between coats depending on temp
and humidity. Each coat should be dry to touch with no tackiness before
applying next coat. Rust-Bite is a moisture cure finish which when applied
too heavy will have a tendency to bubble while curing. Avoid bubbling by
applying thin coats only. Higher temps and humidity will shorten drying
time. Low temp and humidity will lengthen dry. Do not apply Rust-Bite if
temperature is below 50°F. Never use lacquer thinner as a reducer for Rust-
Bite or to wipe surfaces prior to painting.
BRUSH APPLICATION:
Apply thin, even coats using a nylon brush. For better flow and leveling, add
up to 10% TRC-01 Reducer.
SPRAY APPLICATION:
Reduce up to 10% using TRC-01 Reducer. Apply medium-wet coats while
maintaining a gun distance of 12 to 14 inches. Spray tip size should be: 1.2 to
1.4mm.
NOTE:
For surfaces that will be
exposed to UV (sunlight), apply a UV resistant single stage urethane paint after 3 - 24 hours.
RECOAT:
For films cured over 24 hours, sand using 400-grit abrasive to remove
gloss before recoating.
Health and Safety:
See Safety Data Sheet and labels for additional safety information and handling instructions.
* The contents of this package may have to be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels and SDS’s of all components, since
the mixture will have the hazards of all its parts.
* Improper handling and use, for example, poor spray technique, inadequate engineering controls and or lack of Personal Protective Equipment (PPE), may result in hazardous conditions or injury.
* Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
* Provide adequate ventilation for health and fire hazard control.
* Follow company, product SDS and respirator manufacturer’s recommendations for selection and proper use of respiratory protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory
requirements.
* Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on SDS.
* Always observe all applicable precautions and follow good safety and hygiene practices.
* Safety Data Sheets are available on website.
- Brand: Speedokote
- Manufacturer Part Number: TRC-15-Q
- Manufacturer Color Name: Gloss Black
- Size: Quart
- Color: Gloss Black
- UPC: 682821552229
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
| Shipping Method | Estimated Delivery | Cost |
|---|---|---|
| Free Shipping (US) | 5–10 business days | Free, available on eligible items |
| Standard Shipping (US to US by Item) | 5–10 business days | $5.95 for the first item, $3.00 each additional |
| Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $5.95, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
| Extended Delivery (Ships from Overseas Warehouse) | 10–20 business days | $14.50 for the first item, $2.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
- Email: support@ibspot.com
- Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
- The item must be unused, in the same condition as received, and in its original packaging.
- A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
- Perishable goods (for example, food, flowers, newspapers, magazines)
- Intimate or sanitary goods
- Hazardous materials or flammable liquids/gases
- Gift cards
- Downloadable software
- Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
- Books with obvious signs of use
- Opened CDs, DVDs, software, or vinyl records
- Items not in their original condition, damaged, or missing parts not due to our error
- Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
- In-store returns are refunded to the original form of payment or issued as a gift card.
- Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
- 5–7 business days for the return to reach our Returns Center.
- An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.