Restore Pontoon Marine Adhesive Glue for Boat Carpet & Pontoon Vinyl Flooring - 2 Gallons
$200.55
- Free US shipping
-
Arrives
- L590 Marine Adhesive, flooring fabric, and substrate should be acclimatized for at least 24 hours prior to installation. Failure to properly acclimate voids any and all warranties.
- One substrate is prepped as described in the subfloor surfaces section, loose-fit flooring to ensure proper fit.
- User may want to leave a few inches of extra fabric at the edges so that any movement in installation can be corrected.
- After loose-fitting, begin at one end of the boat and roll the fabric (face in) back toward the middle of the work area. Try to work in sections.
- L590 may be brushed on, rolled on, or troweled (w/ 5/32” U-notch trowel). L590 will cure from the outside-in.
- This means if it is left open to the air long enough to form a
"skin”, the adhesive should be immediately scraped off and disposed,
then begin application over with fresh adhesive.
- L590 is not a contact adhesive, therefore there is no need for tack-time. Simply place fabric onto wet adhesive, work out wrinkles, and make adjustments right away.
- Apply L590 to the substrate at a rate of approximately 1 gallon / 120 square feet (heavier applications will take longer to cure.)
- One adhesive is spread, unroll fabric over coated substrate and smooth out any wrinkles with a smooth straight edge (the core that the fabric came rolled on works great)
- Once the area is covered, roll un-glued fabric from the other end, and repeat the application process.
- Open time with vary with temperature and humidity, but once fabric is applied and wrinkles worked out, avoid foot-traffic or weather exposure (including cold temperatures) for 24-48 hours.
- Exact sure times will vary with atmospheric conditions.
- You may check for cure by examining edges, but DO NOT tug at
fabric, as pulling too hard will tear fabric or pull stitches or backing
once adhesive has cured.
- Once 590 has cured, trim any excess fabric from edges with sharp scissors, or roll edges and install j-channel.
- With proper care and maintenance, your new flooring should provide you with years of great service!
Recommended for use with:
- L590 Marine Adhesive is designed for use with synthetic carpets, woven fabrics with marine backs, woven polypropylene (ActionBac), urethane or PVC foams and latex unitary.
- It is water resistant and non-flammable.
- It provides an extremely fast-setting, strong bond.
- L590 is a very versatile and user-friendly adhesive.
Subfloor Surfaces:
- Fiberglass
- Marine grade plywood
- Concrete
- Aluminum
- DO NOT USE over wood surfaces that contain copper salts.
General Prep:
- Aluminum must be sanded with rough-grit sandpaper to remove oxidation and to provide a suitable surface to bond to.
- Fiberglass must be cleaned with solvent to remove any mold release lubricants.
- Gel-coated fiberglass must be sanded with rough-grit sandpaper to achieve a strong bond.
- Wipe surface clean (regardless of substrate) with a tack cloth and
safety solvent before applying L590 to remove cleaning agents, residue,
and dust.
Specifications:
- Open Time: typically, 15-30 minutes (will vary with temperature and humidity)
- Freeze-Thaw Stable (spread-ability can be altered if allowed to freeze)
- If frozen, DO NOT stir adhesive. Allow adhesive to thaw at room temperature and pour off excess water before use.
- Shelf Life: One year in unopened container
- Clean Up:
- Wet: warm water
- Dry: safety solvent
Warranty:
- L590
Flooring Adhesive is manufactured to rigid Quality Control
specifications and warranted to be free of defects. Defective product
brought to our attention within one year of manufacture with be replaced
at no charge to the customer. Warranty claims should be accompanied by
the original receipt and the lot number from the original container. All
claims should be sent to Boat Carpet Central; Attn: Claims; 1923 N.
Home St Mishawaka, IN 46545.
If you have any questions or need further assistance, please contact us at (574) 204-2345
DO NOT USE EXCESSIVE AMOUNTS OF ADHESIVE.
Excess adhesive will require substantially longer cure times. Follow installation instructions on the label.
- Free 30-Day Returns
- Full Refund for Damaged or Incorrect Items
- Guaranteed Delivery or Money Back
- Secure Checkout & Fast Support
- L590 Marine Adhesive, flooring fabric, and substrate should be acclimatized for at least 24 hours prior to installation. Failure to properly acclimate voids any and all warranties.
- One substrate is prepped as described in the subfloor surfaces section, loose-fit flooring to ensure proper fit.
- User may want to leave a few inches of extra fabric at the edges so that any movement in installation can be corrected.
- After loose-fitting, begin at one end of the boat and roll the fabric (face in) back toward the middle of the work area. Try to work in sections.
- L590 may be brushed on, rolled on, or troweled (w/ 5/32” U-notch trowel). L590 will cure from the outside-in.
- This means if it is left open to the air long enough to form a
"skin”, the adhesive should be immediately scraped off and disposed,
then begin application over with fresh adhesive.
- L590 is not a contact adhesive, therefore there is no need for tack-time. Simply place fabric onto wet adhesive, work out wrinkles, and make adjustments right away.
- Apply L590 to the substrate at a rate of approximately 1 gallon / 120 square feet (heavier applications will take longer to cure.)
- One adhesive is spread, unroll fabric over coated substrate and smooth out any wrinkles with a smooth straight edge (the core that the fabric came rolled on works great)
- Once the area is covered, roll un-glued fabric from the other end, and repeat the application process.
- Open time with vary with temperature and humidity, but once fabric is applied and wrinkles worked out, avoid foot-traffic or weather exposure (including cold temperatures) for 24-48 hours.
- Exact sure times will vary with atmospheric conditions.
- You may check for cure by examining edges, but DO NOT tug at
fabric, as pulling too hard will tear fabric or pull stitches or backing
once adhesive has cured.
- Once 590 has cured, trim any excess fabric from edges with sharp scissors, or roll edges and install j-channel.
- With proper care and maintenance, your new flooring should provide you with years of great service!
Recommended for use with:
- L590 Marine Adhesive is designed for use with synthetic carpets, woven fabrics with marine backs, woven polypropylene (ActionBac), urethane or PVC foams and latex unitary.
- It is water resistant and non-flammable.
- It provides an extremely fast-setting, strong bond.
- L590 is a very versatile and user-friendly adhesive.
Subfloor Surfaces:
- Fiberglass
- Marine grade plywood
- Concrete
- Aluminum
- DO NOT USE over wood surfaces that contain copper salts.
General Prep:
- Aluminum must be sanded with rough-grit sandpaper to remove oxidation and to provide a suitable surface to bond to.
- Fiberglass must be cleaned with solvent to remove any mold release lubricants.
- Gel-coated fiberglass must be sanded with rough-grit sandpaper to achieve a strong bond.
- Wipe surface clean (regardless of substrate) with a tack cloth and
safety solvent before applying L590 to remove cleaning agents, residue,
and dust.
Specifications:
- Open Time: typically, 15-30 minutes (will vary with temperature and humidity)
- Freeze-Thaw Stable (spread-ability can be altered if allowed to freeze)
- If frozen, DO NOT stir adhesive. Allow adhesive to thaw at room temperature and pour off excess water before use.
- Shelf Life: One year in unopened container
- Clean Up:
- Wet: warm water
- Dry: safety solvent
Warranty:
- L590
Flooring Adhesive is manufactured to rigid Quality Control
specifications and warranted to be free of defects. Defective product
brought to our attention within one year of manufacture with be replaced
at no charge to the customer. Warranty claims should be accompanied by
the original receipt and the lot number from the original container. All
claims should be sent to Boat Carpet Central; Attn: Claims; 1923 N.
Home St Mishawaka, IN 46545.
If you have any questions or need further assistance, please contact us at (574) 204-2345
DO NOT USE EXCESSIVE AMOUNTS OF ADHESIVE.
Excess adhesive will require substantially longer cure times. Follow installation instructions on the label.
- L590 Marine Adhesive, flooring fabric, and substrate should be acclimatized for at least 24 hours prior to installation. Failure to properly acclimate voids any and all warranties.
- One substrate is prepped as described in the subfloor surfaces section, loose-fit flooring to ensure proper fit.
- User may want to leave a few inches of extra fabric at the edges so that any movement in installation can be corrected.
- After loose-fitting, begin at one end of the boat and roll the fabric (face in) back toward the middle of the work area. Try to work in sections.
- L590 may be brushed on, rolled on, or troweled (w/ 5/32” U-notch trowel). L590 will cure from the outside-in.
- This means if it is left open to the air long enough to form a
"skin”, the adhesive should be immediately scraped off and disposed,
then begin application over with fresh adhesive.
- L590 is not a contact adhesive, therefore there is no need for tack-time. Simply place fabric onto wet adhesive, work out wrinkles, and make adjustments right away.
- Apply L590 to the substrate at a rate of approximately 1 gallon / 120 square feet (heavier applications will take longer to cure.)
- One adhesive is spread, unroll fabric over coated substrate and smooth out any wrinkles with a smooth straight edge (the core that the fabric came rolled on works great)
- Once the area is covered, roll un-glued fabric from the other end, and repeat the application process.
- Open time with vary with temperature and humidity, but once fabric is applied and wrinkles worked out, avoid foot-traffic or weather exposure (including cold temperatures) for 24-48 hours.
- Exact sure times will vary with atmospheric conditions.
- You may check for cure by examining edges, but DO NOT tug at
fabric, as pulling too hard will tear fabric or pull stitches or backing
once adhesive has cured.
- Once 590 has cured, trim any excess fabric from edges with sharp scissors, or roll edges and install j-channel.
- With proper care and maintenance, your new flooring should provide you with years of great service!
Recommended for use with:
- L590 Marine Adhesive is designed for use with synthetic carpets, woven fabrics with marine backs, woven polypropylene (ActionBac), urethane or PVC foams and latex unitary.
- It is water resistant and non-flammable.
- It provides an extremely fast-setting, strong bond.
- L590 is a very versatile and user-friendly adhesive.
Subfloor Surfaces:
- Fiberglass
- Marine grade plywood
- Concrete
- Aluminum
- DO NOT USE over wood surfaces that contain copper salts.
General Prep:
- Aluminum must be sanded with rough-grit sandpaper to remove oxidation and to provide a suitable surface to bond to.
- Fiberglass must be cleaned with solvent to remove any mold release lubricants.
- Gel-coated fiberglass must be sanded with rough-grit sandpaper to achieve a strong bond.
- Wipe surface clean (regardless of substrate) with a tack cloth and
safety solvent before applying L590 to remove cleaning agents, residue,
and dust.
Specifications:
- Open Time: typically, 15-30 minutes (will vary with temperature and humidity)
- Freeze-Thaw Stable (spread-ability can be altered if allowed to freeze)
- If frozen, DO NOT stir adhesive. Allow adhesive to thaw at room temperature and pour off excess water before use.
- Shelf Life: One year in unopened container
- Clean Up:
- Wet: warm water
- Dry: safety solvent
Warranty:
- L590
Flooring Adhesive is manufactured to rigid Quality Control
specifications and warranted to be free of defects. Defective product
brought to our attention within one year of manufacture with be replaced
at no charge to the customer. Warranty claims should be accompanied by
the original receipt and the lot number from the original container. All
claims should be sent to Boat Carpet Central; Attn: Claims; 1923 N.
Home St Mishawaka, IN 46545.
If you have any questions or need further assistance, please contact us at (574) 204-2345
DO NOT USE EXCESSIVE AMOUNTS OF ADHESIVE.
Excess adhesive will require substantially longer cure times. Follow installation instructions on the label.
- Brand: Restore Pontoon
- Manufacturer Part Number: L590
- Featured Refinements: Boat Flooring Adhesive
- Country/Region of Manufacture: United States
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
| Shipping Method | Estimated Delivery | Cost |
|---|---|---|
| Free Shipping (US) | 5–10 business days | Free, available on eligible items |
| Standard Shipping (US to US by Item) | 5–10 business days | $5.95 for the first item, $3.00 each additional |
| Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $5.95, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
| Extended Delivery (Ships from Overseas Warehouse) | 10–20 business days | $14.50 for the first item, $2.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
- Email: support@ibspot.com
- Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
- The item must be unused, in the same condition as received, and in its original packaging.
- A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
- Perishable goods (for example, food, flowers, newspapers, magazines)
- Intimate or sanitary goods
- Hazardous materials or flammable liquids/gases
- Gift cards
- Downloadable software
- Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
- Books with obvious signs of use
- Opened CDs, DVDs, software, or vinyl records
- Items not in their original condition, damaged, or missing parts not due to our error
- Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
- In-store returns are refunded to the original form of payment or issued as a gift card.
- Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
- 5–7 business days for the return to reach our Returns Center.
- An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.