360 LED 7-14 DIY WHITE LED CLUSTER UPGRADE KIT SILVERADO SIERRA TAHOE SUBURBAN AVALANCHE
$96.11
- Free US shipping
-
Arrives
This listing is for an L.E.D. upgrade kit for YOUR cluster in ULTRA BRIGHT WHITE. YOU ARE NOT BUYING A INSTRUMENT CLUSTER If your cluster looks like the one in the picture this kit will work for you. 2007-2014 Avalanche, Denali, Sierra, Silverado, Suburban, Tahoe, Yukon, Yukon XL This L.E.D. upgrade kit consists of enough l.e.d's to upgrade the backlighting of your cluster for the gauges and the needles. Soldering skills are required for this kit. These l.e.d's are fully dimmable. These l.e.d's bulbs are backed by a Forever Warranty. They will never flicker or burn out. The overlay/gauge face in the 07-14 Chevy trucks does not have a blue film on it so you do not need to sand it. Simply solder the new bulbs in and assemble it. This kit is also available in: Pure Blue Golden Yellow Passionate Pink Ultra Violet Purple Ice Blue Ruby Red Emerald Green Rainbow Burst Red, White, and Blue I also have L.E.D. kits available to upgrade your steering wheel controls, headlight and 4x4 switches, door switches, HVAC (heater and A.C.), traction control, fog light, 4x4 selector switch, etc., Contact me if you want to buy additional upgrade kits, or if you would like a custom color scheme. Installation tips: One corner of the led has a small notch removed, use this as a reference. The notch will need to be facing the same direction as the led that you removed. The OEM led's are attached with 4 pads on the circuit board. The new led's only need to be soldered to 2 of those pads. DO NOT USE SOLDER AND FLUX YOU GOT IN THE PLUMBING SECTION OF YOUR LOCAL STORE! That solder is not electrically conductive. Use solder made for electrical work. I use this and it can be purchased on Amazon: Kester 24-6337-0027 Solder Roll, Core Size 66, 63/37 Alloy, 0.031" Diameter ALWAYS USE FLUX!!! This is the flux that I use, and it can also be purchased on Amazon: AMTECH NC-559-V2-TF no-clean tacky solder flux (ROL0) 10cc kit USA 16150K (There are videos on Youtube that will walk you through removal of the cluster and led installation.) DO NOT SOLDER ON A LIVE CIRCUIT BOARD Installation instructions: REPLACE ONE LED AT A TIME! DO NOT REMOVE ALL LEDS AT ONCE! (You'll end up having to send your cluster to me and paying me $200 + shipping to finish your job.) Grab a marker. Remove cluster, take cluster apart. Plug cluster in and turn lights on in truck, identify which l.e.d's are backlighting l.e.d's. Note the orientation of the notch on the stock led before removing it. Remove one OEM l.e.d. Get your multi-meter out and set it to DC Volts. Plug the cluster in and check two pads looking for voltage, if no voltage on the two that you tested test the other two. Identify and label the pads that are supplying voltage. Label positive and negative. Unplug the cluster Flux the pads Solder the new l.e.d in place. Plug the cluster in to test it. Repeat until done. Note: The l.e.d.s that illuminate the needles are right up next to the stepper motor rod and only have 2 pads on the circuit board. These will be easy, you don't need to test them with the volt-meter, simply install your led with the corner notch facing the same direction that the OEM notch was facing. My photos (All photos used in this listing) are my intellectual property. They are watermarked, copyright protected, they are not for sale, and I will prosecute unlawful use and theft of them to the fullest extent of the law. Improper l.e.d. installation is not covered under warranty. |
- Free 30-Day Returns
- Full Refund for Damaged or Incorrect Items
- Guaranteed Delivery or Money Back
- Secure Checkout & Fast Support
This listing is for an L.E.D. upgrade kit for YOUR cluster in ULTRA BRIGHT WHITE. YOU ARE NOT BUYING A INSTRUMENT CLUSTER If your cluster looks like the one in the picture this kit will work for you. 2007-2014 Avalanche, Denali, Sierra, Silverado, Suburban, Tahoe, Yukon, Yukon XL This L.E.D. upgrade kit consists of enough l.e.d's to upgrade the backlighting of your cluster for the gauges and the needles. Soldering skills are required for this kit. These l.e.d's are fully dimmable. These l.e.d's bulbs are backed by a Forever Warranty. They will never flicker or burn out. The overlay/gauge face in the 07-14 Chevy trucks does not have a blue film on it so you do not need to sand it. Simply solder the new bulbs in and assemble it. This kit is also available in: Pure Blue Golden Yellow Passionate Pink Ultra Violet Purple Ice Blue Ruby Red Emerald Green Rainbow Burst Red, White, and Blue I also have L.E.D. kits available to upgrade your steering wheel controls, headlight and 4x4 switches, door switches, HVAC (heater and A.C.), traction control, fog light, 4x4 selector switch, etc., Contact me if you want to buy additional upgrade kits, or if you would like a custom color scheme. Installation tips: One corner of the led has a small notch removed, use this as a reference. The notch will need to be facing the same direction as the led that you removed. The OEM led's are attached with 4 pads on the circuit board. The new led's only need to be soldered to 2 of those pads. DO NOT USE SOLDER AND FLUX YOU GOT IN THE PLUMBING SECTION OF YOUR LOCAL STORE! That solder is not electrically conductive. Use solder made for electrical work. I use this and it can be purchased on Amazon: Kester 24-6337-0027 Solder Roll, Core Size 66, 63/37 Alloy, 0.031" Diameter ALWAYS USE FLUX!!! This is the flux that I use, and it can also be purchased on Amazon: AMTECH NC-559-V2-TF no-clean tacky solder flux (ROL0) 10cc kit USA 16150K (There are videos on Youtube that will walk you through removal of the cluster and led installation.) DO NOT SOLDER ON A LIVE CIRCUIT BOARD Installation instructions: REPLACE ONE LED AT A TIME! DO NOT REMOVE ALL LEDS AT ONCE! (You'll end up having to send your cluster to me and paying me $200 + shipping to finish your job.) Grab a marker. Remove cluster, take cluster apart. Plug cluster in and turn lights on in truck, identify which l.e.d's are backlighting l.e.d's. Note the orientation of the notch on the stock led before removing it. Remove one OEM l.e.d. Get your multi-meter out and set it to DC Volts. Plug the cluster in and check two pads looking for voltage, if no voltage on the two that you tested test the other two. Identify and label the pads that are supplying voltage. Label positive and negative. Unplug the cluster Flux the pads Solder the new l.e.d in place. Plug the cluster in to test it. Repeat until done. Note: The l.e.d.s that illuminate the needles are right up next to the stepper motor rod and only have 2 pads on the circuit board. These will be easy, you don't need to test them with the volt-meter, simply install your led with the corner notch facing the same direction that the OEM notch was facing. My photos (All photos used in this listing) are my intellectual property. They are watermarked, copyright protected, they are not for sale, and I will prosecute unlawful use and theft of them to the fullest extent of the law. Improper l.e.d. installation is not covered under warranty. |
This listing is for an L.E.D. upgrade kit for YOUR cluster in ULTRA BRIGHT WHITE. YOU ARE NOT BUYING A INSTRUMENT CLUSTER If your cluster looks like the one in the picture this kit will work for you. 2007-2014 Avalanche, Denali, Sierra, Silverado, Suburban, Tahoe, Yukon, Yukon XL This L.E.D. upgrade kit consists of enough l.e.d's to upgrade the backlighting of your cluster for the gauges and the needles. Soldering skills are required for this kit. These l.e.d's are fully dimmable. These l.e.d's bulbs are backed by a Forever Warranty. They will never flicker or burn out. The overlay/gauge face in the 07-14 Chevy trucks does not have a blue film on it so you do not need to sand it. Simply solder the new bulbs in and assemble it. This kit is also available in: Pure Blue Golden Yellow Passionate Pink Ultra Violet Purple Ice Blue Ruby Red Emerald Green Rainbow Burst Red, White, and Blue I also have L.E.D. kits available to upgrade your steering wheel controls, headlight and 4x4 switches, door switches, HVAC (heater and A.C.), traction control, fog light, 4x4 selector switch, etc., Contact me if you want to buy additional upgrade kits, or if you would like a custom color scheme. Installation tips: One corner of the led has a small notch removed, use this as a reference. The notch will need to be facing the same direction as the led that you removed. The OEM led's are attached with 4 pads on the circuit board. The new led's only need to be soldered to 2 of those pads. DO NOT USE SOLDER AND FLUX YOU GOT IN THE PLUMBING SECTION OF YOUR LOCAL STORE! That solder is not electrically conductive. Use solder made for electrical work. I use this and it can be purchased on Amazon: Kester 24-6337-0027 Solder Roll, Core Size 66, 63/37 Alloy, 0.031" Diameter ALWAYS USE FLUX!!! This is the flux that I use, and it can also be purchased on Amazon: AMTECH NC-559-V2-TF no-clean tacky solder flux (ROL0) 10cc kit USA 16150K (There are videos on Youtube that will walk you through removal of the cluster and led installation.) DO NOT SOLDER ON A LIVE CIRCUIT BOARD Installation instructions: REPLACE ONE LED AT A TIME! DO NOT REMOVE ALL LEDS AT ONCE! (You'll end up having to send your cluster to me and paying me $200 + shipping to finish your job.) Grab a marker. Remove cluster, take cluster apart. Plug cluster in and turn lights on in truck, identify which l.e.d's are backlighting l.e.d's. Note the orientation of the notch on the stock led before removing it. Remove one OEM l.e.d. Get your multi-meter out and set it to DC Volts. Plug the cluster in and check two pads looking for voltage, if no voltage on the two that you tested test the other two. Identify and label the pads that are supplying voltage. Label positive and negative. Unplug the cluster Flux the pads Solder the new l.e.d in place. Plug the cluster in to test it. Repeat until done. Note: The l.e.d.s that illuminate the needles are right up next to the stepper motor rod and only have 2 pads on the circuit board. These will be easy, you don't need to test them with the volt-meter, simply install your led with the corner notch facing the same direction that the OEM notch was facing. My photos (All photos used in this listing) are my intellectual property. They are watermarked, copyright protected, they are not for sale, and I will prosecute unlawful use and theft of them to the fullest extent of the law. Improper l.e.d. installation is not covered under warranty. |
Condition
Interchange Part Number
Surface Finish
Manufacturer Part Number
Other Part Number
Brand
Fitment Type
Warranty
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
| Shipping Method | Estimated Delivery | Cost |
|---|---|---|
| Free Shipping (US) | 5–10 business days | Free, available on eligible items |
| Standard Shipping (US to US by Item) | 5–10 business days | $5.95 for the first item, $3.00 each additional |
| Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $5.95, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
| Extended Delivery (Ships from Overseas Warehouse) | 10–20 business days | $14.50 for the first item, $2.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
- Email: support@ibspot.com
- Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
- The item must be unused, in the same condition as received, and in its original packaging.
- A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
- Perishable goods (for example, food, flowers, newspapers, magazines)
- Intimate or sanitary goods
- Hazardous materials or flammable liquids/gases
- Gift cards
- Downloadable software
- Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
- Books with obvious signs of use
- Opened CDs, DVDs, software, or vinyl records
- Items not in their original condition, damaged, or missing parts not due to our error
- Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
- In-store returns are refunded to the original form of payment or issued as a gift card.
- Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
- 5–7 business days for the return to reach our Returns Center.
- An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.